Beretta stock refinish

Share your questions on all makes and models of shotguns. Please post chokes questions in the SRBC forum

Moderators: Quack Wacker NC, MM

Beretta stock refinish

Postby Edge » Thu Aug 15, 2013 1:42 pm

Don't try it. I don't know what finish they use, but you will need a jack hammer to get it off. I have been applying Jasco for three days now, I think I need three more, and that's before I can start sanding. Next time I will just buy a new stock.
User avatar
Edge
hunter
 
Posts: 230
Joined: Tue Feb 14, 2012 10:18 am


Re: Beretta stock refinish

Postby 3200 man » Thu Aug 15, 2013 2:25 pm

Just keep sanding until you get down to the plastic , the B models , have some of the best ! :lol3:
3200 man
hunter
 
Posts: 2568
Joined: Thu Nov 12, 2009 10:30 am

Re: Beretta stock refinish

Postby cootlover » Fri Aug 16, 2013 11:55 am

Did you know that some of the Beretta are plastic stocks that look like wood :huh:
cootlover
hunter
 
Posts: 996
Joined: Sun Nov 20, 2011 8:39 pm

Re: Beretta stock refinish

Postby 3200 man » Fri Aug 16, 2013 12:46 pm

I'll be Damn ? You can always order a wood-set from Coles !
3200 man
hunter
 
Posts: 2568
Joined: Thu Nov 12, 2009 10:30 am

Re: Beretta stock refinish

Postby OmegaRed » Fri Aug 16, 2013 1:03 pm

cootlover wrote:Did you know that some of the Beretta are plastic stocks that look like wood :huh:


xtra grain. didn't think they were plastic though, i thought they were lesser wood with a higher quality wood finish.
quacknstack6 wrote:
I'm as good once as I ever was isn't your theme song OG. I hate to burst your bubble.
User avatar
OmegaRed
Fabio
 
Posts: 3178
Joined: Thu Oct 18, 2012 10:38 am
Location: OHIO

Re: Beretta stock refinish

Postby Edge » Sat Aug 17, 2013 4:49 pm

This is an older AL390, the stock actually cost as much as the gun does, because it is Black Walnut. I do not buy plastic guns. But nice try at being funny. I did find out that this is a two part finish and it is hard as nails. It will be another two weeks before I am finished, but I will post a pic.
User avatar
Edge
hunter
 
Posts: 230
Joined: Tue Feb 14, 2012 10:18 am

Re: Beretta stock refinish

Postby 3200 man » Sun Aug 18, 2013 6:49 am

Yea , sorry for the commit ! With all the effort you're putting in the re-finishing it should be really nice , Good Luck !
3200 man
hunter
 
Posts: 2568
Joined: Thu Nov 12, 2009 10:30 am

Re: Beretta stock refinish

Postby Jon Bergren » Sun Aug 18, 2013 7:01 am

I would use Tung Oil or Tung Oil Varnish after staining. Put on seven coats. Tung Oil is the most resistant to water other than Teak Wood Oil which is very expensive. Rub it with 0000 steel wool between each coat. The Tung Oil Varnish will dry faster. It is much better than Linseed Oil with the driers. Ned S
Jon Bergren
hunter
 
Posts: 1353
Joined: Fri Mar 08, 2013 7:07 pm

Re: Beretta stock refinish

Postby Edge » Sun Aug 18, 2013 8:45 am

That's where I am now Jon, first coat went on this morning. However, I did buy a plastic gun yesterday, almost on impulse. I was in my LGS and Jeremie says look at the new 400s, they moved the KO, it's more water proof, woo, woo, woo, and I'll give it to ya for woo. At least now I won't be fighting over the old 400 with my daughter. :fingerhead:
User avatar
Edge
hunter
 
Posts: 230
Joined: Tue Feb 14, 2012 10:18 am


Return to Shotgun Forum

Who is online

Users browsing this forum: Rebel and 14 guests