Boat blind ideas

A duck boat forum to discuss duck hunting boats, mud motors, and everything related.

Moderators: jamesmc, Dogman, NCSUDucker, nitrousneil

Boat blind ideas

Postby Duck Nasty » Sat Jul 05, 2014 1:28 pm

I have a 1648 alumacraft and I want to build a low profile blind does anyone have any pictures of theirs. I've used the search and not finding what I'm looking for. Any help will be greatly appreciated


Sent from hades
User avatar
Duck Nasty
hunter
 
Posts: 465
Joined: Wed Oct 16, 2013 9:58 am
Location: Hampstead nc


Re: Boat blind ideas

Postby KillerKowalski » Sat Jul 05, 2014 2:41 pm

Duck Nasty wrote:I want to build a low profile blind


Define low profile. I have seen houses on some hulls when it was labeled "low profile". What searching have you done? There are many examples available.
User avatar
KillerKowalski
hunter
 
Posts: 1936
Joined: Sun Oct 16, 2011 3:25 pm

Boat blind ideas

Postby Duck Nasty » Sat Jul 05, 2014 2:48 pm

As in provably nothing over 30" over the gunnel. I've searched on here but I'm not liking the blinds such as the Avery or cabelas style pop up blind. I'm looking for some out of the box ideas


Sent from hades
Last edited by Duck Nasty on Sat Jul 05, 2014 3:21 pm, edited 1 time in total.
User avatar
Duck Nasty
hunter
 
Posts: 465
Joined: Wed Oct 16, 2013 9:58 am
Location: Hampstead nc

Re: Boat blind ideas

Postby KillerKowalski » Sat Jul 05, 2014 3:08 pm

Gotcha. This has been a hit on the forums. I copied it and turned out well for the cost. I do not have a link, but you can easily find it on Google Image search. I believe he was 26" above.
Attachments
IMG_0193.jpg
User avatar
KillerKowalski
hunter
 
Posts: 1936
Joined: Sun Oct 16, 2011 3:25 pm

Re: Boat blind ideas

Postby Ichabod97 » Sun Jul 06, 2014 6:41 pm

Built this blind on my 1854 Phowler when I had it. The boat had 30 inch sides and I think the top of the flip tops were just under 32" above the rest of the boat. Concealed the hunters great, but the flip tops got to be a pain in the butt over time. Killed plenty of birds out of it though. Dog hide was on the bow and I had a small opening the dog went out and came up the rear via the hunt deck.

Image

Image

Image

Image

I added more raffia to it after this hunt to help it blend in a little better.


Folded up for transport. The flip tops went on the bow and were secured with bungees.
Image

The framework. The downside of the blind was that it took about 3-5 minutes to set up. I had a lot of braces and pins that went into play to keep the framework from sagging in the middle.
Image

Image

I used camo tarps as the base layer to keep us dry. Worked well in the rain. Only downside was you were hunched over a bit under the flip tops. But the end result is to kill ducks, and we did just that out of this rig.
Image

Netting on top of the tarp to allow for a base layer of camo to attach the raffia too. Overall I think I have about 20lbs of raffia on it to conceal it all. Even had pieces that drapped around the mud motor to conceal it as well.
Image

Image

And proof that the blind worked. 3 man limit of teal in 1 hr on a public WMA.
Image
Nick "Ichabod"
Waterfowl Mafia

Modified Scissor Blind ppt

imaduckin up north wrote:There aint no ducks in VA
User avatar
Ichabod97
State Moderator
 
Posts: 2919
Joined: Wed Apr 07, 2010 7:09 pm
Location: Norfolk, VA / Jacksonville, FL

Re: Boat blind ideas

Postby Cupped-n-Committed » Mon Jul 07, 2014 7:37 am

I don't have any pictures of it right now, but have to take some as I am selling it. I made like a blanket of Cordura that is attached to a conduit bar that clamps to the left side of the boat. It has a 1' that hang to the water and another conduit bar sewed in the end. We pull the boat up to the cover on the right side and have back rests that you lean you head on and pull the blanket over the seats while sitting on the boat floor. You could make a head cover like shown above, but that is higher profile and I was going for as low as possible and you just can't move. The motor is about a full 1' higher than the blind and I made a net with rafia for the front deck and the motor. It used a spud pole also as everyone was on the right side.

Sorry, I can get pictures later this week, if you're really interested.
"If you can't have fun doing it, it ain't worth doing." my motto

There is nothing better than hunting with friends and then crackin' a couple of cold ones afterwards.
User avatar
Cupped-n-Committed
Forum & State Moderator
 
Posts: 2552
Joined: Fri Nov 12, 2004 2:48 pm
Location: Fairplay, MD

Re: Boat blind ideas

Postby Duck Nasty » Mon Jul 07, 2014 5:31 pm

Thanks guys. Cnc I like the idea of what you had. It is the most similar to what I was thinking. I'm looking forward to seeing the pictures.

Ichabold that's good looking but it really looks kind of like the top cover would be somewhat of a hindrance at the moment of impact.

My idea is to make pretty much a cover. I can think of making it somewhat like a coffin blind where you are sitting on the floor of the boat in a very low style beach chair and the doors open the the other perpendicular to the length of the boat. If that makes sense to anybody


Sent from hades
User avatar
Duck Nasty
hunter
 
Posts: 465
Joined: Wed Oct 16, 2013 9:58 am
Location: Hampstead nc

Re: Boat blind ideas

Postby grnhd » Mon Jul 07, 2014 9:07 pm

Nobody gives a crap about your season totals.
grnhd
hunter
 
Posts: 922
Joined: Tue Apr 28, 2009 6:07 am
Location: suwanee,ky

Re: Boat blind ideas

Postby Duck Nasty » Tue Jul 08, 2014 4:51 pm

Yes very similar to what I am trying to do


Sent from hades
User avatar
Duck Nasty
hunter
 
Posts: 465
Joined: Wed Oct 16, 2013 9:58 am
Location: Hampstead nc

Re: Boat blind ideas

Postby threedogs » Wed Jul 09, 2014 9:04 am

Cupped-n-Committed wrote:I don't have any pictures of it right now, but have to take some as I am selling it. I made like a blanket of Cordura that is attached to a conduit bar that clamps to the left side of the boat. It has a 1' that hang to the water and another conduit bar sewed in the end. We pull the boat up to the cover on the right side and have back rests that you lean you head on and pull the blanket over the seats while sitting on the boat floor. You could make a head cover like shown above, but that is higher profile and I was going for as low as possible and you just can't move. The motor is about a full 1' higher than the blind and I made a net with rafia for the front deck and the motor. It used a spud pole also as everyone was on the right side.

Sorry, I can get pictures later this week, if you're really interested.


I'd like to see the pictures . I did the same thing last year but with plywood and it turned out to be a warped up mess !
Thread Killer
threedogs
hunter
 
Posts: 539
Joined: Thu Oct 25, 2012 10:52 pm
Location: Arizona

Re: Boat blind ideas

Postby BKScripto » Wed Jul 09, 2014 12:40 pm

I'd like to see what cupped-n-committed has going on with that blind too. Sounds interesting. Sub'd
User avatar
BKScripto
hunter
 
Posts: 352
Joined: Tue Dec 11, 2012 10:12 pm

Re: Boat blind ideas

Postby Cupped-n-Committed » Wed Jul 09, 2014 1:19 pm

Attachement pf the conduit bar holding the blind on the boat, one at both ends and one in the center.
IMG_0776 - Copy (800x600).jpg
Codura attachement


How the Cordura is held onto the conduit.
IMG_0775 - Copy (800x600).jpg
Conduit Clamp


Large netting secured to the ends and attachment spots to tie raffia too. The free end that hangs over the side has a 2x2 pressure treated board screwed to it for weight. It blew in the wind too much and this weighted it down in the wind.
IMG_0771 (800x600).jpg
Cover with net for Raffia


How the cover rests on the seats in the center.
IMG_0774 (800x600).jpg
Resting on the seat


This is it as its rolled up. The side over hang flips into the boat, the front net and motor net place in. End of blanket with conduit brought to the side and folded again and bound with webbing or Bungee.
IMG_0780 (800x600).jpg
Rolled up


I made boards that rest on the sides as we sat on the bottom and leaned on the sides. The guns just laid on top of the Cordura and net cover. The dog sat between us normally or could lay on the front deck if it was still. I don't have a picture of the spud pole but I made it myself and it was bolted to the stern. A 1" water pipe with a screw on cap. The pipe was drilled ever inch and a hitch pin locked the spud pole to the depth I wanted it to be.
"If you can't have fun doing it, it ain't worth doing." my motto

There is nothing better than hunting with friends and then crackin' a couple of cold ones afterwards.
User avatar
Cupped-n-Committed
Forum & State Moderator
 
Posts: 2552
Joined: Fri Nov 12, 2004 2:48 pm
Location: Fairplay, MD

Re: Boat blind ideas

Postby threedogs » Wed Jul 09, 2014 3:58 pm

Interesting , thanks for the pics . What about where you sat , how did you manage the netting ? Any pics of it set up ?
Thread Killer
threedogs
hunter
 
Posts: 539
Joined: Thu Oct 25, 2012 10:52 pm
Location: Arizona

Re: Boat blind ideas

Postby Cupped-n-Committed » Thu Jul 10, 2014 6:50 am

Belle's Last Hunt. This was my Buddy Joe's (trailman) dog and her last hunt, but is shows the cover and the motor and me in the background. You can see the back side of the boat is exposed, but we hunt shorelines and islands on a river.
look down the length.jpg


from the boat looking out at the decoys.
view from inside.jpg
"If you can't have fun doing it, it ain't worth doing." my motto

There is nothing better than hunting with friends and then crackin' a couple of cold ones afterwards.
User avatar
Cupped-n-Committed
Forum & State Moderator
 
Posts: 2552
Joined: Fri Nov 12, 2004 2:48 pm
Location: Fairplay, MD

Re: Boat blind ideas

Postby Duck Nasty » Thu Jul 10, 2014 7:29 am

That's some good stuff there very similar to what I am going to try it looks great


Sent from hades
User avatar
Duck Nasty
hunter
 
Posts: 465
Joined: Wed Oct 16, 2013 9:58 am
Location: Hampstead nc

Re: Boat blind ideas

Postby threedogs » Thu Jul 10, 2014 8:53 am

I'm glad I read this thread because it got my lazy butt in gear . I still have burlap from my fiasco last year and sice it very seldom rains in AZ I'll do a lite weight cover with pvc pipe on both sides to hold it at water level and support it with a few bungees running side to side . Thx again.
Thread Killer
threedogs
hunter
 
Posts: 539
Joined: Thu Oct 25, 2012 10:52 pm
Location: Arizona


Return to Waterfowl Boats, Motors, & Boat Blinds

Who is online

Users browsing this forum: No registered users and 10 guests